- 您现在的位置：买卖IC网 > Sheet目录323 > DS89C450-K00 (Maxim Integrated Products)EVAL KIT FOR DS89C450
DS89C450 Evaluation Kit
TYPICAL OPERATING CIRCUIT
Figure 2. DS89C450 Evaluation Kit Board Layout
DETAILED DESCRIPTION
The DS89C450 EV kit must be used with the DS89C430/DS89C450 ultra-high-speed flash microcontrollers IC data
sheet and the Ultra-High-Speed Flash Microcontroller User’s Guide ( www.maxim-ic.com/user_guides ) . A complete
description of the bootstrap loader commands and functions is located in Section 15 of the Ultra-High-Speed Flash
Microcontroller User’s Guide .
The DS89C450 EV kit and all of its connectors are defined in the schematics provided in the accompanying
documentation disk. However, a short description of the major components of the board follows.
Power Supplies
The EV kit accepts a DC input supply at J1. The supply should be a 6V to 9V DC supply, center post positive, with
at least 300mA capacity. The exact DC input value of the supply is not important, as the on-board linear MAX1658
and MAX1659 regulators produce fixed 5V and 3.3V for use by the kit circuitry.
While it is possible to supply up to 16V at J1 (the maximum input voltage of the MAX1658 and MAX1659), doing so
results in a large amount of heat dissipation from the board. A small heatsink plane is provided on the backside of
the board beneath the linear regulators, but this may be inadequate at input voltages above 9V. If U1 and U2 are
hot, lower the DC input voltage at J1. Note that many unregulated DC wall plug-in supplies may provide an output
level much higher than their labeled output value if they are lightly loaded.
3 of 13
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DSP56311EVM
KIT EVALUATION FOR DSP56311
DSPAUDIOEVMMB1E
BOARD MOTHER DSP563XX
DSPIC30F2010 DEVELOPMENT KIT
KIT DEV EMBEDDED C
DSTRM-KT-0181A
DSTREAM DEBUG AND TRACE UNIT
DSUT1CSU
SURGE SUPPR NETWORK W/GROUND
DTEL2
SURGE SUPPRESSOR PHONE RJ11/RJ45
DV003001
PROGRAMMER PICSTART PLUS 16C/17C
DV164035
MPLAB ICD3 IN-CIRC DEBUGGER
相关代理商/技术参数
DS89C450-KIT#
功能描述:开发板和工具包 - 8051 Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压:
DS89C450-MNG
功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
DS89C450-MNG+
功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
DS89C450-MNL
功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
DS89C450-MNL+
功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
DS89C450-QNG
功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
DS89C450-QNG+
功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
DS89C450-QNL
功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT